meteohub.de

Strange, I read at WXForum this message:

"Latest version of Meteobridge can read back data from the Davis cloud. This is worse than getting data directly from the Davis console, but is better than nothing. Obvious shortcomings are missing rapidly changing wind speed and direction events, which the ...

Meteobridge needs to receive the data from the ISS same as the 6313 receives data from the ISS. Meteobridge can not receive data back from the WeatherLink Cloud and assume here you are referring to WeatherLink.com to whihc the 6313 would be uploading?


Exacly.
So, in my case, Meteobridge will be ...

Not sure what you are expecting to do? 6313 is a console which reads from a Davis sensor suite and displays/uploads to WeatherLink.com

Meteobridge can receive data from the same Davis sensor suite and then can do various uploads including WeatherLink.com but only if it is a MBNano, not a MBPro ...

Hi,

I bought a Weatherlink 6313, but I didn't find a guide about how to setup Meteobridge to read data from Weatherlink Cloud. I already add the API V2 Key + Secret, but no sensor appears.

I installed a new Weatherlink Live and a MB running on a Raspberry Pi.
I configured everything, but in Live Data > Raw Sensor Data is shown this message:

Data logger momentarily cannot provide data. Please try again in a minute. If it does not show up later, please also check weather station ...

I changed my Davis VP2 from Wifilogger to Weatherlink Live.
WFL was running on my MB, but now the WLL is not working: WLL IP is right and fixed. Did I miss anything in configuration?

Hi,

I configured some Dew Point alarms, to tweed in certain conditions, like this:
alarme1.PNG

There are 10 alarms, each one rising, like this one:
alarme2.PNG
It's posted a tweet once, then appear this error in live tab:

Twitter Upload: 2020-11-13 17:51:51 Error: 2020-11-13 17:51:49 error ...

After many reboots, I got wind sensor.

I have exacly the same problem. Was it solved?

How to avoid a trigger when there is lost of sensor's signal?

Raise: ([th0temp-act=c.1:0] <= 5.0)
Clear: ([th0temp-act=c.1:0] > 6.0)
Messagem: FRIO | Temperatura atual em Westfália, já está abaixo dos [th0temp-act.1:--] °C.

Sometimes it happen, and shows "--°C".

How to avoid a trigger when there is lost of sensor's signal?

Raise: ([th0temp-act=c.1:0] <= 5.0)
Clear: ([th0temp-act=c.1:0] > 6.0)
Messagem: FRIO | Temperatura atual em Westfália, já está abaixo dos [th0temp-act.1:--] °C.

Sometimes it happen, and shows "--°C".

Would be possible to set an alarm condition and post a snapshot from Meteobridge Cam on Twitter? Message + Snapshot instead of just a message.

Do I get it right that it only needs to add "&station=X" to the URL to tell Windy what station the data is good for? This should be easy to add.
Will IDs 0 to 9 be sufficient?

Yes, I added "&station=X" and at the same time start sending data correctly. Now I have duplicated stations (PWS and ...

Thanks gus, it worked! Yes, the only one station that Windy was receiving data was ID 0.
Yes, it would be great if we could set station ID under the Weather Network tab settings.

I have 7 weather stations with MB and the configuration is ok. All show that data is being sent to Windy, however just one appear as PWS, the other 6 stations appear as MADIS and if I check at stations.windy.com/stations, for the 6 stations there is no data bein sent. MB says data is being sent and ...