Search found 9 matches
- Sun Sep 03, 2017 3:06 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Stuck on fast blinking LED Mode during reboot
- Replies: 5
- Views: 3543
Re: Stuck on fast blinking LED Mode during reboot
Yes, it is a PRO purchased last December. I am suspecting a problem with the internal USB stick.
- Sun Sep 03, 2017 1:52 am
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Stuck on fast blinking LED Mode during reboot
- Replies: 5
- Views: 3543
Re: Stuck on fast blinking LED Mode during reboot
I don't believe Internet access is the issue. I have tried both LAN port and WiFi on separate networks without any firewall in place. I also did a factory reset, to no avail.
I get to the same point: fast blinking LED and the device IP address where it just sits.
I get to the same point: fast blinking LED and the device IP address where it just sits.
- Sat Sep 02, 2017 4:26 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Stuck on fast blinking LED Mode during reboot
- Replies: 5
- Views: 3543
Stuck on fast blinking LED Mode during reboot
Hi,
I recently rebooted my device to clear out a loss of IP address problem (happens every few weeks or so) and now I am stuck in the fast blinking LED mode. I am able to access the device through the network (I get the Meteobridge Landing Page (FW 1.4) page), but the network config looks fine. It ...
I recently rebooted my device to clear out a loss of IP address problem (happens every few weeks or so) and now I am stuck in the fast blinking LED mode. I am able to access the device through the network (I get the Meteobridge Landing Page (FW 1.4) page), but the network config looks fine. It ...
- Tue May 09, 2017 1:52 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Update 3.3 Big Scroll template no longer working
- Replies: 3
- Views: 2808
Re: Update 3.3 Big Scroll template no longer working
Thank you. Back to normal.
- Sun May 07, 2017 3:19 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Update 3.3 Big Scroll template no longer working
- Replies: 3
- Views: 2808
Update 3.3 Big Scroll template no longer working
Hi,
My unit updated to 3.3 this morning with a reboot and it only displays the outdoor temperature on the screen in large type--no scrolling to other data--with the BIG-scroll-IMP event configured. I have tried rebooting with the event deleted and reinstating it, only to get the same results.
My unit updated to 3.3 this morning with a reboot and it only displays the outdoor temperature on the screen in large type--no scrolling to other data--with the BIG-scroll-IMP event configured. I have tried rebooting with the event deleted and reinstating it, only to get the same results.
- Fri Jan 20, 2017 2:56 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Constantly losing RF signal
- Replies: 4
- Views: 3702
Re: Constantly losing RF signal
By way of update: reducing the sensitivity appears to have made a significant improvement. I have not seen a drop out for over a day now.
- Wed Jan 18, 2017 3:17 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Constantly losing RF signal
- Replies: 4
- Views: 3702
Re: Constantly losing RF signal
Thanks for the suggestion. I reduced the sensitivity, but cannot do much about the environment. I personally do not use any devices other than the weather station that operate in the 900 MHz band (e.g., cordless phone, Zigbee); I do suspect our local electric utility uses this band for our smart ...
- Sat Jan 14, 2017 6:17 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Constantly losing RF signal
- Replies: 4
- Views: 3702
Re: Constantly losing RF signal
Additional info: the RF environment does not seem to be a problem. Attached is the output from a spectrum analyzer placed next to the MB Pro (you can see the ISS in the background) centered on 915 Mhz. Signal strength consistently is in the -50's and -60's dBm range from the ISS and S/N looks ...
- Sat Jan 14, 2017 4:38 pm
- Forum: Meteobridge PRO/PRO2/NANOSD/RPI/VM Discussion
- Topic: Constantly losing RF signal
- Replies: 4
- Views: 3702
Constantly losing RF signal
Hi,
My Meteobridge PRO cannot maintain reception of RF signals for more than a few hours at a time. I get constant dropouts: sometimes lasting minutes; sometimes hours. The tell-tail sign of a problem shows up in the log as "restart meteostick (301 secs no valid rf signal)". A more complete copy of ...
My Meteobridge PRO cannot maintain reception of RF signals for more than a few hours at a time. I get constant dropouts: sometimes lasting minutes; sometimes hours. The tell-tail sign of a problem shows up in the log as "restart meteostick (301 secs no valid rf signal)". A more complete copy of ...